4.9/5 stars from 1,200+ reviews
Bring dull, worn floors back to life in one coat.
Restore a rich, even shine to sealed hard floors—without sanding, machines, or a contractor. Spread it thin. Let it dry. Watch the whole room look cared for again.
-
✨
A richer, more even dry finish in one controlled coat
-
🧹
No sanding, machines, or contractor
-
▣
500 mL ready-to-use pour-and-spread formula
Before you apply
FloorReset is a finish-restoration coat, not a cleaner. Start with a clean, completely dry, structurally sound floor and use it only on surfaces listed on the bottle label.
Always test a small hidden section first. Do not use on peeling, water-damaged, unsealed, waxed, or oil-finished surfaces unless the bottle label specifically confirms compatibility.
The controlled-coat method
Work in small sections. Spread one thin, even coat and avoid reworking an edge once it begins to level.
Keep people and pets off the area until it is fully dry according to the bottle directions. Judge the result only after dry-down, in the same light you used for the before view.
Shipping
Available shipping methods, costs, and delivery estimates appear at checkout. Tracking is emailed when your order ships.
As seen in
Watch what one coat does after it dries
Same floor. Same light. Fully dry.
One thin coat, spread edge to edge.
The next-day reveal — with real traffic back on it.
Your floor isn’t dirty. Its finish has worn dull.
The Worn-Finish Mismatch
You cleaned it. Then cleaned it again. The dull, cloudy look came straight back.
Here’s why: cleaner lifts dirt. It can’t replace the worn surface that reflects light. FloorReset lays down a thin, clear coat that evens out light wear — so the floor stays richer after it dries.
You see the grain again. The whole room stops looking tired.
Clean. Spread one thin coat. Let it dry. That’s the Controlled Coat Method.
The result that matters starts when the floor is dry
Same angle. Same light. No wet-floor trick.
Before
Fully dry
Same floor. Same light. Fully dry.— FloorReset proof protocol
One coat. Four steps. A floor that looks alive again.
No sanding. No machine. No contractor.
1. Test one square
Choose a hidden spot and make sure the surface is listed on the bottle label.
2. Clean it bare
Remove dirt and residue. Let the floor dry completely.
3. Spread one thin coat
Work section by section. Spread evenly, then leave the drying edge alone.
4. Let the shine set
Keep traffic off until fully dry. Check it in the same light, then finish the room.
THE DRY-DOWN TEST
If the shine disappears when it dries, it doesn’t count.
You’ve seen the videos: a wet floor gleams, the clip ends, and you’re left wondering what happened next.
FloorReset’s proof begins after dry-down. Same floor. Same angle. Same light. A richer, more even finish that’s still there when the wet look is gone.
You see the difference before you finish the room.
CONTROL BEATS GUESSWORK
The “secret” to a streak-free finish is using less.
Heavy pours, old residue and overworked edges cause the haze people blame on the product.
The Controlled Coat Method keeps it simple: clean floor, small section, thin coat, one direction, full dry-down. No random layers. No chasing wet spots.
FOR THE WEAR YOU NOTICE EVERY DAY
Light scuffs fade into a richer, more even finish.
FloorReset is for the dull traffic lanes, cloudy patches and fine wear that make a sound floor look older than it is.
One thin coat evens the way light hits the surface, so those marks stop taking over the room. Deep gouges still need repair. Everyday wear doesn’t need to look permanent.
Before you price a refinish, try one coat.
| FloorReset | Sanding or replacing first | |
|---|---|---|
| Best first step for | Dullness + light cosmetic wear | Deep damage + failing material |
| Disruption | Work in small sections | Move furniture + interrupt the room |
| Equipment | Applicator only | Machines, dust control, or contractor |
| Decision point | One hidden test square | A room-sized commitment |
| Dry-state proof | See the test before continuing | See it after the project |
| Starting investment | $34.99 | Project-sized quote |
Bring the room back for $34.99
One 500 mL bottle. One controlled coat. One chance to restore the floor before turning it into a renovation.
500 mL bottle. Follow the bottle directions for coverage and cure time.
Our customers tell it better than we do!
based on 1 067 reviews
The questions a skeptical floor owner asks first
Is FloorReset a cleaner?
No. Cleaners remove soil. FloorReset is a finish-restoration coat for a clean, dry, compatible surface.
What floor surfaces can I use it on?
Use it only on sealed hard-floor surfaces listed on the bottle label. Always test a small hidden area first. Do not use on unsealed, waxed, or oil-finished surfaces unless the label specifically confirms compatibility.
Will it remove deep scratches or repair damage?
No. It can soften the appearance of fine cosmetic wear by creating a more even visual finish. It cannot fill deep gouges, rebuild missing material, stop peeling, or repair water damage.
What if the floor only looks good while it is wet?
That is exactly why the method starts with one test square and a fully dry reveal. Do not continue across the room until you have judged the dry result in normal light.
How do I avoid streaks, haze, or buildup?
Start clean and completely dry. Use the recommended applicator, work in small sections, spread one thin coat, avoid overworking drying edges, and do not add another layer until you have evaluated the first one fully dry.
Can I apply it over another polish?
Do not mix unknown finish layers. Identify what is already on the floor and follow the bottle label. Residue or incompatible polish can contribute to haze, adhesion problems, and buildup.
Is the result permanent?
No maintenance coat is permanent. Wear depends on traffic, cleaning routine, surface condition, and application. FloorReset is a low-disruption restoration step, not a substitute for professional refinishing when the underlying floor or finish is failing.
How much area will 500 mL cover and how long does it take to dry?
Coverage depends on the floor and how heavily the coat is applied. Work in thin, even sections, then follow the bottle directions for dry time before allowing normal traffic.
One more cleaner won’t bring a worn finish back. One coat of FloorReset will.
You can keep mopping a clean floor and watching the dullness return.
Or spread one thin coat, let it dry, and watch the whole room look cared for again.
Bring your floor back before you replace it.